Composites

Filter

Application

1. Back filling for foundry patterns (1)
2. durability and tear strength. For general mouldmaking where a hard rigid structure is required. (1)
3. fixtures (1)
4. Good release properties (1)
5. Good wetting and impregnating. Pot life and cure time can be varied by using a mixture of H3 & H8 keeping the same mixing ratio. This can be used for thicker laminates. (1)
6. guages (2)
7. jigs (1)
8. large negatives (1)
9. models (1)
10. Moulding of complicated products with precise dimensions. Repetitive casting applications for ceramics (1)
11. negatives & electroforming models. (1)
12. Patterns (1)
13. vacuum casting machines and general mouldmaking. (1)
14. very low shrinkage. (1)
15. Very low viscosity modified laminating resin. (1)
16. Very low viscosity producing good wetting of fibres and fillers. (1)

Pot Life (200g, 25°C) minutes

1. 120 (2)
2. 15-20 (1)
3. 160-220 (2)
4. 18-24 (1)
5. 2-3 hours (1)
6. 20-25 (1)
7. 25-30 (1)
8. 30-50 (2)
9. 30-60 (1)
10. 300-360 (1)
11. 35-40 (1)
12. 40-70 (2)
13. 45-60 (1)
14. 5-6 (1)
15. 50-70 (2)
16. 50-80 (1)
17. 60-70 (1)
18. 60-80 (1)
19. 8-10 (1)
20. 80 (1)
21. 80-140 (1)
22. > 30 (1)
23. data (7)
24. n/a (33)
25. See TDS (10)

Cure Time (25°C) Hours

1. 1 (1)
2. 12 (2)
3. 12-16 (1)
4. 12-24 (1)
5. 16-24 (1)
6. 18-24 (1)
7. 20 (1)
8. 24 (11)
9. 24-48 (1)
10. 24h (2)
11. 3-60s (1)
12. 48 (2)
13. 5-30 sec (1)
14. 5-60 sec (4)
15. 60-90 mins (1)
16. 8-14 (2)
17. data (7)
18. n/a (26)
19. See TDS (11)

Viscosity (25°C) mPa.s

1. 1.3k-1.4k (1)
2. 1000-1500 (1)
3. 1100-1500 (2)
4. 140k (1)
5. 150-250 (1)
6. 180-300 (1)
7. 2-10 (1)
8. 20-40 (1)
9. 2000-3000 (1)
10. 2200-2600 (1)
11. 250-450 (1)
12. 300-600 (2)
13. 30k-70k (2)
14. 350-650 (1)
15. 450-650 (1)
16. 500-1200 (1)
17. 500-800 (1)
18. 600-900 (1)
19. 7000-20000 (1)
20. 80-120 (2)
21. 900-1300 (1)
22. data (7)
23. liquid (1)
24. n/a (26)
25. Paste (4)
26. See TDS (9)
27. thixo (4)
28. Viscous (1)

HDT °C

1. 100 (2)
2. 103-109 (1)
3. 105 (1)
4. 108-112 (1)
5. 110-115 (1)
6. 110-120 (1)
7. 130 (2)
8. 133-139 (1)
9. 140 (1)
10. 150-160 (2)
11. 170 (2)
12. 50 (1)
13. 50-60 (1)
14. 55 (2)
15. 56-60 (1)
16. 57-61 (1)
17. 59 (1)
18. 60 (2)
19. 60-65 (3)
20. 63-67 (1)
21. 68 (2)
22. 70-75 (1)
23. 70-80 (1)
24. 73 (1)
25. 75 (1)
26. 76-80 (1)
27. 79-83 (1)
28. 80 (5)
29. 82-86 (1)
30. 88-92 (1)
31. 90 (1)
32. 90-95 (1)
33. data (4)
34. n/a (18)
35. See TDS (8)
36. TBC (1)

Shore Hardness

1. 10D (1)
2. 23D (1)
3. 35-45A (1)
4. 36-45A (1)
5. 44D (1)
6. 50D (1)
7. 54D (1)
8. 60A (1)
9. 66 (1)
10. 70-75D (1)
11. 70D (2)
12. 72D (1)
13. 73D (1)
14. 74D (1)
15. 75D (2)
16. 76D (1)
17. 78-82D (3)
18. 80-85 (1)
19. 80-85D (4)
20. 80-90A (1)
21. 80D (1)
22. 82-87D (2)
23. 83-87 (1)
24. 83-87D (4)
25. 83D (1)
26. 85-88D (1)
27. 85-90D (6)
28. 85D (1)
29. 86-90 (1)
30. 87-92 (1)
31. data (7)
32. n/a (18)
33. See TDS (4)
34. TBC (2)