Jigs & Fixtures

Filter

Application

1. Back filling for foundry patterns (1)
2. Best selling resin system for Vacuum forming tools. large volumes can be cast with slow hardener. (1)
3. copy models (1)
4. fast reproduction models and prototypes. (1)
5. figurines. (1)
6. fixtures (1)
7. For casting and backfilling. Good edge stability. (1)
8. Foundry patterns (1)
9. gauges (2)
10. guages (1)
11. jigs (1)
12. large negatives (1)
13. Low viscosity for detail. Pattern and modelmaking. (1)
14. models (3)
15. negatives (2)
16. negatives & electroforming models. (2)
17. Patterns (3)
18. Pre- fabricated frames (1)
19. Pre- fabricated support frames and vacuum forming moulds. (1)
20. Produces ultra fine detail and dimensional stability. (1)
21. Prototypes (1)
22. prototypes and bulk casting. (1)
23. Reproduction models (1)
24. vacuum forming tools. (1)
25. very low shrinkage. (1)

Pot Life (200g, 25°C) minutes

1. 10-12 (1)
2. 120 (1)
3. 120-180 (2)
4. 180-240 (1)
5. 2min15 - 2min45 (1)
6. 3-4 (1)
7. 3-5 (1)
8. 35-45 (1)
9. 3min30 - 4min30 (1)
10. 4-5 (1)
11. 43-53 (1)
12. 5min30 - 7min (1)
13. 7-9 (1)
14. 8-11 (1)
15. 80-130 (1)
16. n/a (6)

Cure Time (25°C) Hours

1. 10-25 mins (1)
2. 12-16 (2)
3. 12-24 (3)
4. 15-40 mins (2)
5. 2-4 (2)
6. 20-25 mins (1)
7. 24 (2)
8. 30-50 mins (1)
9. 50-60 mins (1)
10. 6-8 (1)
11. n/a (6)

Viscosity (25°C) mPa.s

1. 10000-15000 (1)
2. 120-220 (1)
3. 12000-16000 (1)
4. 12000-18000 (1)
5. 1500 (1)
6. 250-350 (1)
7. 40000-60000 (1)
8. 45-85 (1)
9. 50-100 (1)
10. 60-100 (2)
11. 70-90 (1)
12. 80-140 (1)
13. n/a (6)
14. Paste (1)
15. thixo (2)

HDT °C

1. 100 (1)
2. 110 (1)
3. 116-122 (1)
4. 140 (1)
5. 50 (1)
6. 50-60 (2)
7. 60-65 (2)
8. 62-67 (1)
9. 65-70 (1)
10. 67-72 (1)
11. 70-80 (1)
12. 73 (1)
13. 75 (2)
14. 80 (2)
15. 90 (1)
16. n/a (1)
17. See TDS (2)

Shore Hardness

1. 50D (1)
2. 63-68A (1)
3. 67-72D (1)
4. 70-75D (3)
5. 75-80D (2)
6. 75D (1)
7. 80-85D (2)
8. 80D (1)
9. 83D (1)
10. 85-89 (1)
11. 85-90D (1)
12. 85-95D (1)
13. 86-90 (1)
14. 87-92D (1)
15. 90-95D (1)
16. n/a (3)